News

The Right Product for the Job

Wednesday, February 12th, 2014

by David Taper and Steven Atkey – Fairford’s Technical Sales Engineers

We all make large efforts to try and choose the right product for a job; we all know the saying “using a sledge hammer to crack a nut”. This is exactly what is happening every day in industry, consumers are using products that are not specifically designed for the job in hand, this causes excess expenditure, inefficient systems and in some cases failures this is all due to the wrong equipment being used. In this short article we will investigate different methods for starting motors and highlight the applications and industries where selecting the correct product can dramatically improve the overall system efficiencies.

The options for starting an AC induction motor are many and varied everything from the simple contactor; Soft Starter; variable speed drive (VSD); Energy Saving Soft Starter to name a few. VSD’s are becoming the preferred starting method for some consumers however this may not always be the most efficient or suitable starting method.

VSD’s use Insulated Gate Bipolar Transistors (IGBT’s) to vary the frequency supplied to the motor this will change the speed of the motor to vary the output and will also give a ‘soft start’. This variable speed option is essential to some processes, for example a production line that needs to vary speeds of their motors for different products.

VSD’s can provide good energy savings on applications that have the ability to be slowed down due to the cube law affect. Slowing the motor down by 20% will give a reduction of energy consumption of 50%. Good applications for this feature are pumps and fans which often supply more water or air than the process requires allowing for the motor to be slowed down the output reduced and thus save energy.

The little known negative effects of VSD’s is that if they run at full speed (or frequency) they use more energy, around 3 – 5% in losses and produce more harmonics than other starting methods for example DOL or Soft Starters. So there are options for improving system efficiencies by simply choosing the right product.

Simple Soft Starters will remove these inefficiencies when the motor is running at full speed due the fact that they have an internal bypass contactor which, once the motor is up to speed will act like a contactor and thus have little or no losses attributed to it. It is a common misconception that VSD’s are the best solution to start and run your motor but if the motor is running at full speed there are other better solutions.

There is another technology that not only will improve the system efficiencies but will, in many instances, reduce the energy consumption of the motor being controlled. These technologies are called Energy Saving Soft Starters. They utilise an Energy Saving algorithm and the more advanced systems use an internal bypass contactor to give an overall system efficiency improvement. The applications that are perfectly suited to this technology are systems that run at full speed with a light or variable load, for example refrigeration compressors, injection molding machines, escalators, hydraulic pumps, artificial lift pump jacks and many more.

The Soft Starter market has seen further advancements in this field of Energy Saving with the development of ‘iERS’ Intelligent Energy Recovery System. iERS continually monitors the motors power factor to deduce the loading of the motor, the system will then make changes to the amount of voltage and current supplied to the motor to reduce the energy consumption and improve the part load power factor.

iERS will decide when there are no benefits from Energy Saving (for example when the load is above 50%) and will energise the bypass relays achieving no losses from the Soft Starter.  When the motor/load falls below 50% loading iERS will de-energise the bypass relays and enter the Energy Saving sequence again.

What does this mean to you?

In 2012 a trial installation was undertaken on an artificial lift pump jack in Texas the aim of this trial was to see how much energy could be saved when comparing to a direct on line starter, Energy Saving Soft Starter and a VSD.

The pump jacks have a cycle where they are lightly loaded and fully loaded. This application lends itself perfectly to the Energy Saving Soft Starter because in the light load stages good amounts of energy saving were realised, 17% on average. When the figures were analysed the Energy Saving Soft Starter gave much greater savings.

When running at full speed the pump will extract a certain amount of oil. When the motor is slowed down by VSD control it has to work for longer to see the same amount of oil produced. Specifically with pump jacks the leakage plays a larger part in the system efficiency because the slower the rod moves the more oil escapes.

In this example an Energy Saving Soft Starter contributes to greater overall system efficiency saving valuable time and money.

In conclusion selecting the correct piece of equipment for the job is more important than the headline energy savings advertised. Using an Energy Saving Soft Starter on a fixed speed motor will save more energy than using a VSD.

Leading control gear specialist, distributors, system integrators OEM’s and end users all have seen the benefits of using VSD’s and Soft Starters together, using the benefits of both systems in a package that will provide the most efficient solution and the most viable cost effective package.


Back


Fairford has the capability to design and manufacture bespoke motor control solutions for OEMs and Industrial Automation vendors.

Latest Tweets

Following the successful launch of a new product we have vacancies for Product Assembly Technicians. Apply at… https://t.co/f7SnDzaqQG
1 hour

In #Kuwait we have Gulf-Tech Automation as one of our many global sales partners. See https://t.co/NH8vPPhfnL https://t.co/HAd72Y3XIp
1 day

We are seeking Product Test Technicians to support our portfolio of innovative products and growing order book. See… https://t.co/FGE8YmYMMz
1 day